Overstock and closeout items. Great deals, while supplies last!
AMERIMAX HAND TONGS - aluminum hand tong seamers with all three blade sizes: 3.5 inch, 7 inch AND 10 inch blades. Save money when you buy the tongs and the extra blades at the same time! Aluminum hand tong seamers with all three blade sizes: 3.5 inch, 7 inch and 10 inch.
Fairmont MT14000 Straight Hand Tongs and Seamers
If you do any flashing work, you need at least one set of heavy-duty hand tongs. Made in the USA. Fairmont tongs are preferred by professionals. Select Standard Grip or Cushion Grip Below.Three inch wide jaw will bend sheet metal 1 1/8 inches deep. Tool is 9.5 inches long overall and weighs 1.82 pounds.Fairmont tongs are forged and plated and fully guaranteed against defective material and workmanship. Used to fold seams on flat seam work, to bend metal into mortar joints when reflashing chimneys, and for general sheet metal or copper work.Made in the USA by Klenk Tools.
Fairmont MT14010 Offset Hand Tongs and Seamers
This classic, professional tool is a variation of the straight tongs. The offset model is a handy variation of the straight tongs. Three inch wide jaw will bend sheet metal 1 1/8 inch deep. Tool is 9.5 inches long overall and weighs 1.82 pounds. Made in the USA.Fairmont tongs are forged and plated and fully guaranteed against defective material and workmanship. Used to fold seams on flat seam work, to bend metal into mortar joints when reflashing chimneys, and for general sheet metal or copper work. Made by Klenk Tools.
Stortz Model 83B Right-Handed or 83C Left-Handed Slate Hammer (select below).This is the traditional German-made slate hammer with the beveled shank for cutting roof slate on site. Forged of high quality tool steel and made to the most exacting standards.Point, claw and hammer face are specially heat treated to withstand tough use. The claw at center is made for pulling nails without damaging the slate. The beveled edge on the midsection is used for trimming slate, along with a slaters stake. An all-leather handle is included.
23 ounces (650 grams). Face 3/4 inch X 7/8 inch, 12.75 inches long, 8.5 inch head
A slate hammer is a necessary tool for any slate roofer. It’s lightweight, multi-purpose, and is easily used on the roof. The major functions of a slate hammer are to cut and trim slate, punch holes in slate, and to drive nails during installation. Cutting thicker slates (thicker than a quarter inch) is also possible with the use of a hammer and stake. This slate hammer is not meant to be used to hit the back on a slate ripper to remove slate. Use a slaters restoration hammer for beating on rippers such as the Picard 0079010 Roofers Hammer.
- A checkered face allows for less grazing and slips when hitting nails.
- The point of a hammer is used for punching holes in slate.
- The double sided nail claw is versatile both ways to remove nails.
- The beveled shank is used for trimming slate in combination with a slater's stake.
- A bell patterned leather handle provides comfortable to grip.
Model 51000 (left handed). Hand-forged hammer made in Germany, fully heat-treated and polished, fitted with an all leather bell-style grip. Left handed models only.The nail puller is slotted on the sides of the claw. Square checkered hammer face offers sharp corners. Beveled shank for cutting slates. 23.7 ounces (672 gm), 12.75 inches long, 8.5 inch head, 3/4 inch X 3/4 inch face. Use this hammer with a slaters stake when cutting slate.
Standard European-style carpenter's hammer, also a perfect slate roof restoration hammer useful for all types of construction work, including framing. Anyone who works on slate roofs should have one of these. The hammer is designed for slate roof repair, restoration, and installation. A Slate Roof Warehouse exclusive and you can't beat this price anywhere! Free shipping in the USA (not including Alaska and Hawaii).
The weight is in the head, not the shank, so it's ideal for beating on a slate ripper and for pounding roofing nails all day long. Punches nail holes in roofing slates.
This is a well-balanced hammer with a comfortable rubber grip. It weighs 28 ounces, is 12 inches long and has a 6 3/4 inch long head. It has a smooth face and no magnet. Made in China.
This European-style carpenter's hammer is designed for slate roof repair and restoration, slate roof installation, and general construction. The weight is in the head, not the shank, so it's ideal for beating on a slate ripper and for pounding nails all day long.
You can't find a slating hammer at this price anywhere but here. Pointed claw punches nail holes in roofing slates. This is a well-balanced hammer with a comfortable contoured rubber grip. It weighs 28 ounces, is 12 inches long and has a 6 3/4 inch long head. It has a cross-hatch face and a magnet. Made in China.
FREE SHIPPING ON THIS PRODUCT (Alaska and Hawaii not included)!
Best aviation snips on the market. Designed for professional use. 10 1/2 inches long, right, left or straight cut. This is a hard to find tool!
Newly redesigned Reimann Georger Ladder Hook with rolling wheel (an inch of length has been added to the lower hook). This heavy-duty ladder hook has a swivel angle iron end as well as a non-swivel rolling wheel. Use one hook per ladder. 4.7 pounds, 20 1/2 inches long overall, 6 inch swiveling plate at tip of hook. Assembly required. Made in the USA.
Secure almost any single ladder section to your roof. The ladder hook is especially helpful when working with weak decking, wet or icy surfaces, steep slopes, and chimney or antenna repairs. The wheel makes it easy to roll on the roof. The swiveling end plate distributes the weight of the ladder to prevent breakage of slates, tiles, or asbestos shingles.
Top-quality, German slate hammer for all types of slate roofing work. Also makes a great all-around hammer for carpentry and construction. Solid steel (not tubular) shank, rugged and comfortable two components grip. Features a cross-hatch face and a magnet in head for holding iron nails.
This hammer weighs 2.10 pounds (33.60 ounces) or 952.54 grams overall. 12.5 inches long, 7 inches wide head. Pointed claw end punches holes in roofing slate. Great for slate roof restoration work as it can beat on a slate ripper with ease. This, along with the Picard 0079010, are our two best general roofer's hammers. You can't go wrong when you buy this tool.
Top-quality, German slate hammer for all types of slate roofing work. Also makes a great all-around hammer for carpentry and construction. Solid steel (not tubular) shank, rugged and comfortable, leather grip. Features a cross-hatch face and a magnet in head for holding iron nails.
This hammer weighs 2.05 pounds (32.8 ounces) or 929.86 grams overall. 12.375 inches long, 7 inches wide head. Pointed claw end punches holes in roofing slate. Great for slate roof restoration work as it can beat on a slate ripper with ease. This, along with the Picard 0059010, are our two best general roofer's hammers. You can't go wrong when you buy this tool.
American Beauty Model 3178, 300 Watt
* WATTAGE - 300 Watts
* REPLACEMENT HEATING ELEMENT NUMBER - 9277
* MAXIMUM TIP TEMPERATURE (F) - 1000°F
* MAXIMUM TIP TEMPERATURE (C) - 538°C
* OVERALL LENGTH - 14 3/8 inches (36.5cm)
* TIP SHANK DIAMETER - 7/8 inch (22.2mm)
* TIP LENGTH - 5 5/32 inches (13.1cm)
* PRODUCT WEIGHT - 37 ounces (1.05 kg)
* SHIPPING WEIGHT - 4 pounds (1.81 kg)
* COUNTRY OF ORIGIN - US
Our most popular electric soldering iron. The American Beauty Model 3178 300-Watt Soldering Iron is an industrial-duty iron especially designed for sheet metal applications and provides a 1,000°F maximum tip temperature to assure an even solder flow. Featuring a pre-tinned tip that seats inside the heating element, consisting of a compression-wound resistive wire around a steel spool, this soldering iron is built for optimum heat transfer and has a rugged stainless steel case.
Equipped with a hardwood handle for a sure grip and a heat shield for safety, the American Beauty Model 3178 300-Watt Soldering Iron eliminates propane, acetylene and natural gas and stays hot without open flames. Measuring 14-3/8 inches L overall, it has a 5-5/32 inches L tip x 7/8 inch diameter shank, weighs just 37 ounces and comes with a standard chisel style Paragon soldering tip; diamond style is optional.
American Beauty heavy-duty irons are ideal for heavy soldering jobs and production-line environments. Created by compression winding a special Ni-Chrome heating alloy onto a steel spool, all elements demonstrate an unsurpassed heat capacity and outstanding durability. Protective casings cut from a single block of steel are strengthened with multiple heat treatments and precision brazed for optimal strength and efficiency.